Routing with Cisco 2500 and 1000 Series for LAN-ISDN Service

Commands - General

There are 3 different modes of operation within the Cisco IOS.

1. Disabled mode
2. Enabled mode
3. Configuration mode

In the Disabled mode you can use a limited number of commands. This is used primarily to monitor the router.

The Enabled mode is used to show configuration information, enter the configuration mode, and make changes to the configuration.

The Configuration mode is used to enter and update the runtime configuration.

To get a list of the commands for the cisco type '?' at the prompt. To get further information about any command, type the command followed by a '?'.

clear	Reset functions
clock	Manage the system clock
configure	Enter configuration mode
debug	Debugging functions (see also 'undebug')
disable	Turn off privileged commands
enable	Turn on privileged commands
erase	Erase flash or configuration memory
exit	Exit from the EXEC
help	Description of the interactive help system
login	Log in as a particular user
logout	Exit from the EXEC
no	Disable debugging functions
ping	Send echo messages
reload	Halt and perform a cold restart
setup	Run the SETUP command facility
show	Show running system information
telnet	Open a telnet connection
terminal	Set terminal line parameters
test	Test subsystems, memory, and interfaces
traceroute	Trace route to destination
tunnel	Open a tunnel connection
undebug	Disable debugging functions (see also 'debug')
verify	Verify checksum of a Flash file
write	Write running configuration to memory, network, or terminal
show
access-lists	List access lists
arp	ARP table
buffers	Buffer pool statistics
configuration	Contents of Non-Volatile memory
controllers	Interface controller status
debugging	State of each debugging option
dialer	Dialer parameters and statistics
extended	Extended Interface Information
flash	System Flash information
flh-log	Flash Load Helper log buffer
history	Display the session command history
hosts	IP domain-name, lookup style, name servers, and host table
interfaces	Interface status and configuration
ip	IP information
isdn	ISDN information
line	TTY line information
logging	Show the contents of logging buffers
memory	Memory statistics
privilege	Show current privilege level
processes	Active process statistics
protocols	Active network routing protocols
queue	Show queue contents
queueing	Show queueing configuration
reload	Scheduled reload information
route-map	route-map information
running-config	Current operating configuration
sessions	Information about Telnet connections
smf	Software MAC filter
stacks	Process stack utilization
startup-config	Contents of startup configuration
subsys	Show subsystem information
tcp	Status of TCP connections
terminal	Display terminal configuration parameters
users	Display information about terminal lines
version	System hardware and software status

Other Useful Commands

View the Software Version
View the Ethernet IP
View the Serial IP
View the Default Route
View the Filters
View the Bandwidth
Add a Static Route
Change the Dial Number
Turn Filters On and Off
Ping from the Router
Traceroute from the Router

View the Software Version

Cisco>en Cisco#wr term    <--- Shows the running configuration     Building configuration... Current configuration: ! version 11.2 no service udp-small-servers no service tcp-small-servers ! hostname Cisco ! interface Ethernet0  ip address 192.168.1.1 255.255.255.0 ! interface Serial0  ip address 192.168.6.1 255.255.255.0  encapsulation frame-relay  frame-relay lmi-type ansi ! interface Serial1  ip address 192.168.4.2 255.255.255.0  encapsulation frame-relay  bandwidth 1536  keepalive 5  frame-relay map ip 192.168.4.1 101 IETF ! router rip  version 2  network 192.168.4.0  network 192.168.6.0  neighbor 192.168.6.2  neighbor 192.168.4.1 ! ip classless ip route 0.0.0.0 0.0.0.0 192.168.6.2 ip route 0.0.0.0 0.0.0.0 192.168.4.1 ! line con 0 line aux 0 line vty 0 4 login ! end 

View the Ethernet IP

Router#wr term

This will show the running configuration. Within the configuration, you will see an interface ethernet 0 section:
interface Ethernet0 ip address 38.150.93.1 255.255.255.0 no ip directed-broadcast 

View the Serial IP

Router#wr term
Within the configuration, you will see an interface serial 0 section:
interface Serial0 ip address 38.21.10.100 255.255.255.0 ip broadcast-address 38.21.10.255 ip access-group 106 in encapsulation frame-relay bandwidth 56 no fair-queue frame-relay map ip 38.21.10.1 500 IETF 

View the Default Route

Router#wr term
Within the configuration, you will see an ip route section. 
In the ip route section, look for a route: ip route 0.0.0.0 0.0.0.0 38.167.29.1 The last ip address is the POP ip. 

View the Filters

Router#wr term
Under interface serial 0, look for:
ip access-group 104 in ip access-group 105 out
This means that access-group 104 is the inbound filter set and access-group 105 is the outbound filter set. Then, continue to look in the configuration for the access-list statements:
(Example access-list statements) access-list 104 deny   ip 38.166.101.0 0.0.0.255 any access-list 104 permit tcp any any established access-list 104 permit tcp any eq ftp-data any gt 1023 access-list 104 permit udp any eq domain any gt 1023 access-list 104 permit udp any eq domain any eq domain access-list 104 permit icmp any any access-list 104 permit udp any eq snmp any gt 1023 access-list 105 deny   ip any 38.166.101.0 0.0.0.255 access-list 105 permit tcp any any established access-list 105 permit tcp any any eq ftp access-list 105 deny   udp any eq netbios-ns any access-list 105 deny   udp any eq netbios-dgm any access-list 105 permit ip any any 

View the Bandwidth

Router#wr term
Within the config, you will see an interface serial 0 section:
interface Serial0 ip address 38.21.10.100 255.255.255.0 ip broadcast-address 38.21.10.255 ip access-group 106 in encapsulation frame-relay bandwidth 56 no fair-queue frame-relay map ip 38.21.10.1 500 IETF 

Add a Static Route

Cisco#config t Enter configuration commands, one per line.  End with CNTL/Z. Cisco(config)#ip route DEST.DEST.DEST.DEST MASK.MASK.MASK.MASK GATE.GATE.GATE.GATE where: DEST.DEST.DEST.DEST = The destination network the static route is for        MASK.MASK.MASK.MASK = The subnet mask of the destination network        GATE.GATE.GATE.GATE = The gateway of the static route Example route statement: ip route 38.222.75.0 255.255.255.0 38.20.5.1 Cisco(config)#^Z (hit  z)
Write the entry to memory:
Cisco#wr mem Building configuration... [OK] 

Change the Dial Number

Type en to put the router in enable mode:

test.com>en

The password should be the same as the one used to telnet in.
Password:
To view the router's configuration, type:
test.com#show config
There will be a line in the configuration that says:
dialer map IP 38.1.1.1 speed 64 name LD3330 2707000
The 2707000 is the dial number.

NOTE: Record what interface the dialer map IP line is under because you will need to  use that interface when changing the number. 
Type config t to configure from terminal.
test.com#config t
Enter configuration commands, one per line.  End with CNTL/Z. Enter the interface that the dialer map IP line is under:

test.com(config)#interface BRI0

Add in the new dialer map IP line with the new phone number:
test.com(config)#dialer map IP 38.1.1.1 speed 64 name LD3330 [new number]

Now, remove the old dialer map IP line. To remove a line, type no and then the line. For example, to remove the old dialer map IP, type:

test.com(config)#no dialer map IP 38.1.1.1 speed 64 name LD3330 2707020
Now leave config mode:

test.com(config)# [control] z

Save changes:
test.com# write mem Building configuration... [OK]
Verify the new number is in the config:
test.com#show config
The new number should be in the dialer map IP line.

Turn Filters On and Off

To turn the filters off: 
Router#configure terminal Router(config)#interface Serial0 Router(config-if)#no ip access-group 104 in Router(config-if)#no ip access-group 105 out Router(config-if)# Hit CTRL-Z Router#wr mem Building configuration... [OK] Router#
To turn the filters on: 

Router#configure terminal Router(config)#interface Serial0 Router(config-if)#ip access-group 104 in Router(config-if)#ip access-group 105 out Router(config-if)# Hit CTRL-Z Router#wr mem Building configuration... [OK] Router#

Ping from the Router

Cisco#ping  Example: Cisco#ping 38.8.14.2